Electrodes / Sensors

Bus-capable connection digiLine - Jumo

Intelligent, bus-capable connection system for digital sensors in liquid analysis.

With JUMO digiLine, JUMO presents a bus-compatible connection system for digital sensors in liquid analysis which also offers Plug and Play functionality. 

JUMO digiLine Opens the Door to Sensor Technology 4.0
JUMO digiLine enables simple construction of sensor networks in which sensors are connected to each other in a star or tree structure. A single shared signal line is used for communication with the next evaluation unit or controller. This way plants in which several parameters need to be measured at the same time in different places can be wired efficiently and quickly.

Conductive and inductive conductivity sensor digiLine CR e Ci - Jumo

Digital measurement of inductive and conductive conductivity, now with IO-Link.
Another step in Jumo’s intelligent measurement technology with new conductivity sensors, which expand JUMO’s transmitters range for digiLine digital communication bus.
 
The new smart transmitters are available in various mechanical and electrical installation configurations, perfectly adjusted for each application, with inductive and conductive sensors to measure electrolytic conductivity.
 

Conductive two-electrode conductivity sensor BlackLine CR-GT/-EC/-GS - JUMO

This conductivity sensor from the BlackLine family is available in versions GT, EC, and GS.

The GT version features a special graphite as the electrode material. The graphite has been especially treated to achieve - in conjunction with suitable evaluation devices – measuring ranges up to 100 mS/cm and above.
A temperature probe can optionally be integrated. The conductivity sensor with 120 mm fitting length and a shaft diameter of 12 mm can be used in combination with standard pH or redox electrodes in suitable built-in fittings. The sensor is also ideally suited for linking with handheld or laboratory measuring equipment. When used as an online sensor, suitable flow-through fittings must be employed.

Conductivity sensor for water technology ecoLine Ci – JUMO

The sensor detects the electrolytic conductivity of a process liquid. It uses the inductive principle of measurement. Because it uses the inductive method of measurement rather than the conductive 2-pin or 4-pin measurement method, the sensor is virtually maintenance-free.
 
The sensor detects the electrolytic conductivity of a process liquid and the measuring accuracy is practically unaffected by accumulations and grease or oil film on the surface of the sensor.
A (Pt1000) temperature sensor acquires the process temperature at the same time. The temperature sensor can either be exposed in a stainless-steel pocket (ultra-fast response) or be located right inside the plastic body (with PVDF, only the internal option is possible).

Digital optical sensor digiLine O-DO S10 - Jumo

Jumo digiLine O-DO S10 the digital optical sensor for dissolved oxygen in aqueous solutions.

The sensor's latest optical technology enables precise measurement with long-term stability in fish breeding, sewage treatment plants, as well as other water and wastewater technology applications. The integrated analog and digital interface allows easy connection to field devices and process control systems.
 

Measuring sensor - CTI-750 - Jumo

Inductive conductivity/concentration and temperature transmitter with switching contacts.
 
The device is used for measurement/control of the conductivity/concentration of fluid medium. The application is particularly recommended in media in which severe deposits through contamination, oil, grease, or plaster/calcium precipitations are to be expected. The integrated temperature measurement allows a precise and quick temperature compensation that is particularly important when measuring the conductivity. Additional functions, such as the combined toggling of measuring range and temperature coefficient, allow the optimum use in CIP processes.

Two integrated switching outputs can be freely programmed for limit value monitoring of conductivity/concentration and/or temperature. Alarm and control tasks (desalination) can also be assigned.
 

Optical Sensor for Turbidity Measurements ecoline NTU - Jumo

The turbidity measurement according to DIN EN ISO 7027 is a tried-and-tested method for monitoring water with low to medium levels of turbidity.
 
The measuring principle is based on the infrared measurement according to the 90° scattered light method. Due to the light measurement in the wavelength of 880 nm and the wide measuring range of 0 to 4000 NTU the possible uses of the sensor include quality control and assessment of drinking water as well as wastewater control. The Jumo ecoLine NTU saves its calibration data and history directly into its sensor electronics. As a result, the device is quickly set up and ready for use everywhere, without requiring constant recalibration. The sensor design stands out due to its lean and durable construction. In addition, various immersion and flow fittings are available for installation.
 

pH/Redox single-rod electrodes tecLine - Jumo

Jumo tecLine electrodes are high-quality sensors for professional applications in the process and industrial measuring technology.
 
The use of high-quality materials and components is the distinguishing feature of these electrodes. They are designed as combined single rod measuring electrodes (glass or metal and reference electrode in one shaft). Depending on the type, an optional temperature probe can also be integrated.

Suitable versions are available to meet the most varied requirements. Jumo tecLine sensors are state-of-the-art for modern pH and Redox electrodes. Each electrode is a high-quality product and individually inspected.
 

Transmitter for digital or analog interface, digiLine pH/ORP/T – JUMO

This transmitter permits transmission of the measured value from the sensor to the measuring or automation device via digital bus communication or as an analog signal. The digital device version of the transmitter has a 5-pole M12 plug connection – the analog version an 8-pole one.
 
The 5-pole digiLine electronics supports plug & play operation on the JUMO AQUIS touch S/P or in Modbus operation on the JUMO mTRON T.
 
  • 0
  • 1