Online store
Probe configurator

Hand-held pH, redox and temperature measuring units HND-R - Kobold

The Kobold hand-held pH, redox and temperature measuring units of the HND-R106 model are compact and universally applicable measuring units for electrodes with BNC plug connection. An extensive selection of electrodes makes it possible to use the HND-R106 in almost all application areas.
The Kobold HND-R106 measuring unit offers functions like minimum/maximum value memory, hold function, auto off function and automatic temperature compensation. In addition to pH, Redox and temperature measurement, the device can display the relative humidity value. This is calculated from the measured Redox-value and the previously measured or manually entered pH-value.
View detail

IN SITU gas analyser GM32 – Sick

The GM32 is a In situ gas analyzer for SO2, NO, NO2, NH3, Temp., O2 (Option) 

The GM32 in-situ gas analyzer measures the reactive gases SO2, NO, NO2 and NH3 as well as pressure and temperature in the gas duct - directly, fast and without gas sampling and transport. With this your process systems work with the true values in “real time”. Thanks to self-monitoring you can rely on the measurement results at any time. And in case of a malfunction an early warning will be shown in time. For emission measurement of SO2 and NO, GM32 is tested for suitability according to the new European standard EN 15267-3.
View detail

IN SITU gas analyser GM35 – Sick

GM 35 In situ gas analyzer for carbon monoxide, carbon dioxide and water.
Either simultaneously or as individual measurements: the GM35 measures CO, CO2 and humidity concentrations as well as temperature and pressure quickly, easily and economically. Due to its in-situ measurement technology the GM35 detects the measuring values directly in the gas stream without gas sampling. Reliability, precision and short response time of the analyzer offer a key advantage for efficient control loops in all CO and CO2 generating processes.
View detail

IN SITU gas analyser GM700 - Sick

Measurement of gaseous components under difficult conditions In-situ and extractive technology.

High reliability and precision as well as minimal response times are the distinguishing features of the GM700 Laser gas analyzer. Based on the principle of TDLS and by using specific light absorption the GM700 from Sick is able to measure several gas components, such as NH3, HF, O2 or HCl.

The in-situ measurement is ideal for the fast determination of gas concentrations in process control and emission monitoring. 
View detail

Measuring sensor - CTI-750 - Jumo

Inductive conductivity/concentration and temperature transmitter with switching contacts.
The device is used for measurement/control of the conductivity/concentration of fluid medium. The application is particularly recommended in media in which severe deposits through contamination, oil, grease, or plaster/calcium precipitations are to be expected. The integrated temperature measurement allows a precise and quick temperature compensation that is particularly important when measuring the conductivity. Additional functions, such as the combined toggling of measuring range and temperature coefficient, allow the optimum use in CIP processes.

Two integrated switching outputs can be freely programmed for limit value monitoring of conductivity/concentration and/or temperature. Alarm and control tasks (desalination) can also be assigned.
View detail

Mercury measuring analysers MERCEM300Z - Sick

Innovative measurement of mercury in flue gases.

The MERCEM300Z mercury measuring system from Sick, monitors Hg emissions in flue gases with high reliability within the smallest measuring ranges (0 ... 10 µg/m³).

Due to its rugged housing, MERCEM300Z is suitable for the use in harsh industrial environments. Thereby the complete extractive system is designed to meet national and international regulations and directives.
View detail

Multichannel measuring device for liquid analysis - Aquis Touch S – Jumo

The Jumo AQUIS touch S and P multichannel devices provide a central platform for displaying and further processing a wide variety of measurands in the field of liquid analysis. The devices have a modular design, feature numerous interfaces, and can therefore be adapted entirely according to the individual requirements of each operation. In addition to recording measured values, up to four independent control loops can be implemented. Important process values can also be saved in a tamper-proof manner using an integrated paperless recorder.

Thanks to user-configurable screen masks and a clearly arranged menu navigation, Jumo AQUIS touch S and P are incredibly easy to operate via their touchscreens, despite the wide range of functions.
View detail

Multitec® BioControl 4/8 – Sewerin

Combined stationary measuring device with mobile gas meter.

The Multitec® BioControl is a combined measuring device consisting of the Multitec® BioControl fixed installation and a mobile gas measuring device, namely the Multitec® 540/545.

Depending on the version of Multitec® BioControl, the gas composition and volume can be automatically measured and monitored at up to eight measurement locations. The Multitec® 540/545 measures the values at the individual measurement locations sequentially. The values are transferred to the Multitec® BioControl via an interface.

The mobile gas measuring device must be regularly maintained to guarantee accurate measuring results. The Multitec® BioControl allows easy maintenance for the versions with four and eight measurement locations as standard, with automatic calibration and adjustment with test gas.
View detail

Optical Sensor for Dissolved Oxygen - ecoLine O-DO – Jumo

The Jumo ecoLine O-DO is an optical sensor for dissolved oxygen for measuring dissolved oxygen in aqueous solutions.
Due to integrated pre-amplification and digital signal processing the sensor has a high interference immunity. The measured value for dissolved oxygen is automatically compensated for temperature, air pressure, and salinity (salt content) and then transmitted to the connected display unit with controller over a digital interface. An easily-replaceable optical membrane cap makes the sensor extremely easy to maintain. The current calibration data is directly saved in the sensor electronic. As a result, the Plug and Play function of the system is enabled without necessary recalibration. Inside the sensor is a log book with the last ten successful calibrations available as ring buffer.
View detail

Optical Sensor for Turbidity Measurements ecoline NTU - Jumo

The turbidity measurement according to DIN EN ISO 7027 is a tried-and-tested method for monitoring water with low to medium levels of turbidity.
The measuring principle is based on the infrared measurement according to the 90° scattered light method. Due to the light measurement in the wavelength of 880 nm and the wide measuring range of 0 to 4000 NTU the possible uses of the sensor include quality control and assessment of drinking water as well as wastewater control. The Jumo ecoLine NTU saves its calibration data and history directly into its sensor electronics. As a result, the device is quickly set up and ready for use everywhere, without requiring constant recalibration. The sensor design stands out due to its lean and durable construction. In addition, various immersion and flow fittings are available for installation.
View detail

Particle and flow analyzer Combiprobe CP100 - Sick

Combined measurement of dust, volume flow, pressure, and temperature.
The Combiprobe CP100 is the combination of a DUSTHUNTER SP100 scattered light dust measuring device and a FLOWSIC100 PR volume flow measuring device on a flange plate. The combined probe also features a pressure transmitter and a resistance thermometer. The Combiprobe CP100 only requires a single mounting opening in the funnel in order to measure the dust concentration, volume flow, pressure and temperature. This means that there is considerably less outlay on installation than if the individual components were to be installed separately.
View detail

Particles analyser DUSTHUNTER SB50 - Sick

Scattered light dust monitor with backward scattering.

The DUSTHUNTER SB50 is a measuring device for dust at low to high concentrations in challenging applications, e.g. in hot or corrosive gases. The measurement is based on the backward scattering of light. Installation is made from one side only. Two different penetration depths are possible. Automatic compensation of background light, therefore no light absorber necessary.
View detail

Particles analysers DUSTHUNTER SB100 - Sick

Scattered light dust monitor with backward scattering.

The DUSTHUNTER SB100 is a type-approved measuring device for dust at very low to high concentrations in challenging applications, e.g. in hot or corrosive gases. The measurement is based on the backward scattering of light. Installation is made from one side only.
Two different penetration depths are possible. Automatic compensation of background light, therefore no light absorber necessary. An automatic check of zero and reference point as well as a contamination monitoring is integrated in the device.

At a glance For very low to high dust concentrations; One-side installation; Contamination monitoring; Automatic check of zero and reference point; Automatic compensation of background radiation, therefore no light absorber necessary; For medium to large duct diameters.
View detail

Particles analysers DUSTHUNTER SF100 - Sick

Scattered light dust monitor with forward scattering.

The DUSTHUNTER SF100 is a type-approved measuring device for dust at very low to high concentrations along the whole duct diameter. The measurement is based on the forward scattering of light. The automatic self-alignment optimizes the position of the measuring beam and prevents incorrect measurement. An automatic check of zero and reference point as well as a contamination monitoring is integrated in the device.

At a glance For very low to high dust concentrations; Contamination monitoring; Automatic check of zero and reference point; Automatic self-alignment; For small to medium duct diameters.
View detail

pH single-rod electrodes – tecLine - Jumo

Jumo tecLine electrodes are high-quality sensors for professional applications in the process and industrial measuring technology.
The use of high-quality materials and components is the distinguishing feature of these electrodes. They are designed as combined single rod measuring electrodes (glass or metal and reference electrode in one shaft). Depending on the type, an optional temperature probe can also be integrated.

Suitable versions are available to meet the most varied requirements. Jumo tecLine sensors are state-of-the-art for modern pH and Redox electrodes. Each electrode is a high-quality product and individually inspected.
View detail

Portable gas analyser– 310 - Testo

Entry Level' Flue Gas Analyzer
The testo 310 Flue Gas Analyzer combines simple functions with a high level of measurement accuracy, and is perfect for all basic measurements on heating systems. 

Long battery lifetimes of up to 10 hours guarantee high availability. It’s easy handling and compact design make the testo 310 a robust tool for daily work – even when things get rough. 

The printer specially developed for the testo 310, including infrared interface, allows you to create clear reports on site as required. The current measurement value can be printed out of any measurement menu during or after the measurement.
View detail

Portable, digital pH / redox and conductivity measuring devices 202710 - Jumo

The measuring devices of product group 202710 are battery-operated hand-held units intended to define the following measured values: pH value, Redox potential and temperature, or conductive conductivity and temperature respectively in laboratories, industrial plants, in waste water treatment, in fish-keeping or fish-farming, etc.  
The devices feature a min. and max. value memory and a hold function.
To extend the longevity of the battery, the device can be automatically shut down within a time span of 1 minute to 2 hours. Continuous measuring is also possible. The devices are operated using a membrane keypad.
View detail

PowerCEMS gas analyser – Sick

PowerCEMS power plant analyzer system. 
Efficient CEMS system for power plants.
PowerCEMS50: Certified quality – Easy installation – Easy to use
The PowerCEMS analyzer system is a continuous emission monitoring system specifically designed to meet the emission monitoring requirements of fossil-fuel fired power stations. The basic system uses extractive analyzers coupled with a complete sample conditioning system to measure the typical gas components required for emission measurement including CO, NOx, SO2, and O2. Through standardized design and construction, the PowerCEMS analyzer system is provided at an attractive price and with the superior quality of performance required for industrial use. 
View detail

Sensor de condutividade digiLine CR e Ci - Jumo

View detail

Software MEAC 2000 - Sick

Emission data evaluation system: Data acquisition and storage;  Evaluation and reporting;  Data output and display.
View detail

Tunnel analyser - VISIC100SF – Sick

The VISIC100SF tunnel analyser is an all-in-one solution for measuring visibility, CO, and NO concentrations. It is the only product of its kind in the world to combine the scattered light measurement principle with electrochemical cells - all in one compact housing.
The VISIC100SF is very easy to mount, operate, and maintain. There is no need for alignment or configuration - so you can start measuring right away. With its IP6K9K enclosure rating, not only is the VISIC100SF able to withstand the harsh ambient conditions inside the tunnel; it can also endure tunnel washing operations without any problems. During the design phase, particular importance was attached to ensuring reliable operation and long maintenance intervals.
View detail

Tunnel analyser- FLOWSIC200 - Sick

The FLOWSIC200 from Sick is used for the contact-free and accurate measurement of flow velocity and flow direction inside tunnels or exhaust ventilation ducts. 

Ultrasonic technology provides the cross-sectional mean average value of the flow velocity. This device is used for measurement necessary for optimal ventilation control and reducing running costs to a minimum when air flow is dictated by climatic conditions or by traffic.
View detail
Page 2 of 2
  • 0
  • 1
We use our own and third-party cookies to offer you a better experience and service. To know which cookies we use and how to disable them, read the cookies policy.
By ignoring or closing this message, and unless you have disabled cookies, you agree to its use on this device.